s not possible for the mower to do this. Solutions?
Garden
3 years old, belt is fine and correctly placed, tension pulley replaced, back up safety swithches have been checked, PTO switch has been checked, battery is fine.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it. Need help finding your model number? The PTO switch provides power to the PTO clutch.
If the PTO clutch is not receiving power, the clutch solenoid is defective, or the clutch itself is worn out, the blades will not engage. Since a PTO clutch is not repairable, you will need to replace a broken or worn out clutch with a new one.
Other things that could cause this issue are bad fuel, weak/colapsed/kinked fuel line, faulty spark plug, faulty ignition/coil, oil over full, clogged air filter, plugged/dirty carburetor, worn engine parts internal rings/valves/etc.
The pulleys in your lawn tractor are driven by the drive belt, and turn the spindles. If a pulley doesn`t spin freely, it can cause the engine to die when the blades are engaged. To check the pulleys for sticking and damage, first remove the drive belt from the engine pulley and lift the lever to engage the blades.
Powershift PTO engagement problems could be from blocked hoses or fittings, bad connections or ground or the solenoid. Mechanical PTO engagement problems could originate from low air pressure, improper cable installation or back lash too tight.
If/when the PTO exceeds the preselected RPM setting, the EOC will de-energize the solenoid valve, disengaging the PTO.
Your lawnmower may stop running when hot due to an overheated engine, air leaks, a clogged fuel system, or the carburetor not getting enough gas. It is also possible that the engine is not cooling as it runs because of a dirty air filter. Finally, worn-out pistons may also be the problem.
Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas. If this doesn`t work, you might need a new fuel filter.
The most common reason for a surging lawn mower engine is a blockage in the fuel supply, but there are other possibilities: Bad gas. Bad spark plug. Dirty/faulty carburetor.
Mower blades are spinning 4000 RPMs. An unbalanced blade spinning that fast will cause a significant amount of vibration, which will put stress on yout blade shaft, spindle, and even the engine.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I have a Craftsman FS5500 48″ lawn mower. The PTO makes a noise (squeak) for a second when I pull up on the red blade engage knob. The blades do not engage. PTO does not turn. When I push the red button down to disengage there is a brief squeak from the PTO.
It worked well the past month then a little problem 2 weeks ago. It seemed to disengage after mowing a while. Then after sitting for 15 minutes the blades would engage. I used it earlier this week and the PTO won’t turn at all.
Just purchased from the last and original owner a month ago. He said the oil would need to be changed this summer. Could that be part of the problem? Engine runs great!
Also, I need an owners manual, not able to find from the previous owner.
Thanks
ANSWER : Hi,The problem is probably in the button that you pull and push to engaged and disengage the PTO… If you wiggle the button or try to pull it slowly, you may find a spot where it will work. But the button has gone bad and will need to be replaced.If you are comfortable with wiring, you could jumper the wires and getting it working, but it would be a very temporary and possibly dangerous fix…
Mower won’t start
ANSWER : This may sound stupid but don’t mean it to…
Have you tried with the choke all the way open? Do you have an automatic cruise? Is the right (correct) pedal being pushed in? These will affect if it starts or not. Also if your drive belt or one of the other belts not being tight enough will affect if it starts or just turns over. Not too many things can stope it from starting with new/good battery AND if its getting gas. Try cleaning your gas line and obviously making sure there is no obstruction around or near your blade, if it does start with blade engaged that is :))
If it doesn’t start with blade engaged, well make sure it’s in neutral. Mine won’t start in reverse but will in forward or neutral.
Hope it helps.
Anthony
PTO CONTROLS. How do you engage and disengage PTO.
ANSWER : The tractor is not a 6300 is it.If it’ not you need to adjust the cable for the p.t.o. until it will stay down.Don’t turn the turnbuckle too much at a time because there is a fine line between the won’t engage and the won,t disengage adjustment.
Toro 149cc Lawn Mower Won't Start – Toro Lawn Mower With Toro Power Tools
ANSWER : Bad carburetor your old fuel jammed up the jet so it won’t get fuel and if it does it will start and shut off So replace the carb or try to clean the jet and run non oxy fuel only
Engine dies if i engage blades or take my foot off the brake
ANSWER : You likely need to replace the brake switch,the seat switch can also cause the same problem.Most likely problem is the seat switch,i would try that first.The pto or the reverse switch can cause a shut down but not until you try to mow,seat switch is the most suspect.
My mower will start but won't stay running – Toro LX466 22HP Lawn Tractor 13RT61RH244
ANSWER : I am going to respond 2 times to this post. The first reply will be generic things to check.
First off check the oil level and make sure it is serviced to full.
If your having a lack of fuel (runing lean) you will need to check fuel flow at the carb fuel mainfold. It should fill a spray paint can lid in less than 10 seconds but teting flow rated of the main fuel line. If you have poor flow here… you need to check the fuel filter and the fuel tank outlet port for obstructions.
Good Fuel flow still shutting off…. remove the carb float bow and clean the debris from the bow’ and the treaded area where the fuel solenoid mounts Additionally you will have to again remove the main fuel line and spray carb cleaner in the float needle area to flush out any debris through the fuel hose connection.
For the second response I need to know which engine is installed on your mower by MODEL number if you can locate it. (there are 3 engines) At least try to find the engine model number. If you can not locate it Brand and HP of the engine (I assume 22 hp) Thanks for choosing FixYa,
Kelly
My toro 6.5 hp push mower (2010), has no fire to the plug. I have not abused it. i have a small yard and it just gets normal use. Now it won’t fire. I first changed the fuel and cleaned the carb thinking it was that crappy ethanol again. but i grounded out the spark plug and cranked it…no spark. I think it has to do with the lever you pull back to start it . they have some stupid complicated safety contraption that rides along the fly wheel when you pull back on the handle for starting and shutting off the engine. …it looks worn out already…like a mini brake pad. any ideas?…do i really have to replace this garbage every year or am i on the wrong path here?
ANSWER : Unhook your wire from the coil that goes to shut off mechanism, and see if you have spark then. the wire may be grounded out, or your coil might have took a ****
25 hp kolhler won’t stay running
ANSWER : Check fuel filter, it may be clogged, if so replace