Husqvarna

How to adjust carb

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

This adjustment screw is responsible for adjusting the chainsaws idle. Begin by turning the T screw clockwise until the chainsaw chain begins to move. As soon as you notice it moving, turn the T screw counterclockwise slowly until the chainsaw chain stops.
If your carburettor has a main jet adjustment screw at the base of the float bowl, turn the screw clockwise until you feel it just touch the seat inside the emulsion tube. Then, turn the screw counterclockwise 1 to 1-1/2 turns. Replace the air cleaner assembly and start the engine for final carburettor adjustments.
If your chainsaw bounces around when making contact with the wood, it means that that chains teeth are not grabbing on and ripping through the wood. A sharp chain will cut in a uniform and straight line.
Q: How Do I Know if My Carburetor Needs Adjusting? A: Simply put, poor running conditions are a dead giveaway. A rough idle, poor throttle response, and excessive fuel consumption are all signs to look for. If the carburetor was sitting for some time or hasn`t been serviced in a while, you may need to clean it first.
Power output: 4.5 kW / 6.03 hp. Maximum power speed: 9300 rpm. Idling speed: 2500 rpm.
Q: How Do I Know if My Carburetor Needs Adjusting? A: Simply put, poor running conditions are a dead giveaway. A rough idle, poor throttle response, and excessive fuel consumption are all signs to look for. If the carburetor was sitting for some time or hasn`t been serviced in a while, you may need to clean it first.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Carb screws need adjusted i need to know the settings
ANSWER : Hi. Lightly seat the low screw and bring it out one and a quarter turns. Lightly seat the high and bring it out one turn. Adjust idle screw to suit. Regards Phil.

Read Full Q/A … : Husqvarna

Need to know what the carb adjustments are for a model 61 husky
ANSWER : Low side one turn out from bottem.high sie is the same.after saw is running readjust both high and low.make sure the side dosen’t go in any more then 3/4 of a turn out……if it does you will burn up the saw….

Read Full Q/A … : Husqvarna

How do you get to the throttle jets huskvarna 130BT blower
ANSWER : The 130 has a rotary style carb, so the only adjustment is down through the top of the throttle spindle, you will need a very small flat blade screw driver, the screw down here will lift or raise the needle in the carb, there may well be a plastic plug to remove before you can get deep enough to adjust it.

Read Full Q/A … : Husqvarna

How to adjust a carbretor how to set the jets on a 670 super champ
ANSWER : I’d suggest removing all idols then re-inserting evenly(about 3-4 full turns each to start)/or screw them all the way in and work backwards,then while engine is running tweak them (again evenly) until the engine runs at about 1250rpm without throttle or choke. basically as long as all 4 carbs are set identically and the revs are good your done.this videos of a dodge but its the same principle http://www.youtube.com/watch?v=J8ikzcaMWg0

Read Full Q/A … : Husqvarna

What are the settings for the zama carb on a 330 homelite chainsaw
ANSWER : 1 1/4 turns out. Then let it warm up and adjust in up to 1/8

Read Full Q/A … : Husqvarna

What tool is required to adjust the carb. on a 142e husquvarna chainsaw?
ANSWER : Http://www.ehow.com/how_7241334_adjust-husqvarna-carburetor.html

Read Full Q/A … : Husqvarna

Poulan chain saw after carb rebuild.
ANSWER : Is thereadjustment somewhere on the saw
I think there is 2 .

Read Full Q/A … : Husqvarna

Car settings stihl 026 with wt 194 carb?
ANSWER : Hi Alan CowartBefore you remove or try to adjust your low and high speed jets you should always count the number of turns it takes to lightly seat the idle mixture screw and high speed needle adjusting screws. Be sure to write the number of turns down on a piece of paper so you will know how many turns from the seated position to open the jets when you go to reinstall them, or if you remove them for cleaning or replacement.If you have aready tried to adjust them then the adjustments below should get it running for you for final adjustment when warm.Normally you will adjust your idle jet to 1/2-3/4 turn open from the bottom seated position.Then you will re-adjust the low speed of the engine when the engine is warm by turning the idle screw in or out till the engine runs smoothly at idle speed, around 1200 RPM.The high speed jet is adjusted to 1 1/2- 1 3/4 open from the bottom seated position, after the engine is warm. Then re-adjusted by turning the High Speed jet adjustment screw in or out till the motor runs smoothly at high speed.Alway use the “lightly seated” method if you have not changed the screw settings.

Read Full Q/A … : Husqvarna