3003 008 8921 Rollomatic E Laminated Sprocket Tipped Chain…

Experienced gardeners share their insights in answering this question :
1. Check that the sprocket on the bar tip actually turnas and is free from obstruction.2. Check chain tension is not too tight. 3. Check that you have taken the chain brake off. (pull the front hand guard back until it clicks)4. If you have checked all the above, check the clutch.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Exclusive to STIHL: 3/8″ Picco Micro 3 (PM3) saw chain. This saw chain was specially designed for light, compact chainsaws and ensures less kickback and lower vibration levels. It combines exceptional cutting performance and quality with great user comfort.
The chainsaw chain should feel snug but still pull freely.
Stihl Picco Micro Comfort 3 Chain is a low-vibration low-profile saw chain with the high cutting performance of a standard chain combined with reduced kickback tendency. An all-purpose chain for use on light chain saws. Ideal for all users who appreciate power as well as comfort.
3/8″ has the same rivet measurement as 3/8LP but has a larger cutting tooth and deeper drive link than 3/8LP.
From a design standpoint, 3/32″ and 1/8″ chains are basically the same except for the width between the plates. ´╗┐Some people believe 1/8″ chains are inherently stronger or more durable due to their width. However, there is no strength or durability advantage to being wider.
Generally speaking, the chain should be a little loose on the chain saw guide bar, but not loose enough that the drive links come out of the bar nose. The bar links should feel like they are raising up, but not actually come out of the guide bar. Testing the tension of the chain is a fairly easy task.
The fuel line may be clogged from stale fuel deposits, more reasons to cause your chainsaw to cut out when applying throttle. If a fuel line is cracked, it will leak gasoline and draw air from outside into the fuel line. If the line is leaking fuel, it needs to be replaced.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

3003 008 8921 will start but the chain will not spin.
ANSWER : 1. Check that the sprocket on the bar tip actually turnas and is free from obstruction.2. Check chain tension is not too tight. 3. Check that you have taken the chain brake off. (pull the front hand guard back until it clicks)4. If you have checked all the above, check the clutch.

SAW WONT START IT HAS FIRE TO THE PLUG AND IT WONT START WHEN I SHOOT A LITTLE ETHER IN IT
ANSWER : If the engine has good compression, and good spark, it should at least ‘pop’ several times. Check the flywheel ‘key’ as it may have sheared causing the ignition to be out of time. Hope this helps!

Chain saw chain is loose
ANSWER : Loosen the side cover nuts, then turn the adjuster CW to bring the chain up to the lower edge of the bar, then check to see if the chain will move fairly easily by hand. Tighten the clamp nuts and recheck tension. If chain seems to get loose quickly again, it may not be sharpened correctly causing heat to build in the chain. You should see no reflection of light from the cutting edges if filed correctly and the saw should require very little pressure for it to cut rapidly. Hope this helps!

Just getting started with a new RCS1835. The motor goes but the chain isn’t engaged. Is there another brake I need to release?
ANSWER : The plastic safety kick back may be engaged. 1) unplug the saw. 2) push the kick back safety ahead then pull it back ( it is the guard in front of the handle)
Now if your electric motor is turning, but the chain sproket is not, it may well be the clutch. Tap it with a small hammer, make sure it is free and not hanging up.

Stihl blower will not start – Stihl 18" Chain Saw Bar 3005 008 4717
ANSWER : Check your abc’s of engines first
(intake,fuel) substitute a tiny amount of raw gas in carb intake to see if it springs to life !
(compression) -pull rope slowly to “feel” the piston move up in cylinder to meet resistance , then down again
(combustion,spark) – remove spark plug from engine and place nearby the hole (don’t hold it !!!) and pull saw over briskly look for spark near tip of plug

Can’t keep pole saw running. It starts fine but when i go to do something it shuts down
ANSWER : It sounds to me like you have a blockage in the high jet. There are 2 jets in the carb a HI and a LOW. If you can determine which is the high jet turn it in gently while counting how many full turns and any partial turn and write it down. (example 2 and one half turns) Then remove the high jet needle valve. Spray some carb cleaner into the hole you took the needle valve out of using the little tube that comes with the can of carb cleaner. then put the needle valve back in and turn it gently till it stops again. Now turn it back out the same amount that you wrote down. It would not hurt to do the other jet as well…

Poulan 4018 pp4018 – Poulan P4018 18Inch 40cc 2Cycle Gas Powered Easy Start Chain Saw With Case
ANSWER : Proper fuel mixture?

Chain keeps falling off – Poulan 18" Chain Saw Replbar (small Saws)
ANSWER : Your chain is too loose. If you’re using an old chain, you might need to have a link taken out of it. You can find replacement chains for your saw at Hyperparts.com. Use the application lookup link at the top of the page with your model # to make sure you order the right chain.